As the number of planned projects increased, it became clear that we needed a set of standards which would allow them to communicate with a central computer and each other. It is not practical to have a separate computer, separate wiring, and a separate communications protocol for every project.
The 4E network uses a combination of half and full duplex RS485 and RS232. Some devices have a dedicated line back to the server while others are on a bus.
The latest version of the 4E network is half duplex RS485 in a bus configuration. The Walcott lounge and bathroom have use this.
The 4E network requires one twisted pairs.
Each bathroom recieves 2 cat 3 cables for Bemix, one for signal and one for power. The signal cable is pinned as shown below
|Green with white||Tx/Rx+|
|White with green||Tx/Rx-|
|Orange with white||unused|
|White with orange||unused|
|Blue with white||Left audio|
|White with blue||Audio ground|
|Brown with white||Right audio|
|White with brown||Audio ground|
For the power cable, all colored wires are +12V and all white wires are ground.
The portmaster serial port server is accessed through telnet:
- administrative-port 23
- serial port 0-port 6000
- serial port 1-port 6001
- serial port 30-port 6030
4E Network Protocol
All data sent over the 4E network is encapsulated in packets. The packet format is outlined below:
- header code (2 bytes) = escape character + header character
- header (3 bytes)
- data (variable length)
- end code (2 bytes) = escape character + end character
- escape character = '\'
- header character = 'H'
- end character = 'E'
The header contains three 1 byte fields:
- destination address: This allows the server to route packets from one client to another.
- source address: This allows one client to respond to a request made by another client.
- port: This tells the device what type of data to expect and how to processes it.
Note: If the escape character needs to be transmitted in the data block, two should be transmitted instead.
Data and Ports
Currently, only three ports will be implemented:
- 31 - debug
- 32 - ping
- 64 - Bemix
Other possible ports include:
- EEPROM - for storing data that is currently hardcoded but shouldn't be
- programming - so the PICs can download their own software
- cocoa pot
- other projects
Each device, including the server, is a assigned a unique address.
- 0 = unused
- 1 = server
- 66 (B) = Bemis
- 67 (C) = control panel
- 71 (G) = shallow goodale
- 87 (W) = shallow walcott
- 92 (\) unused
- 255 = broadcast, all devices listen
How to control Bemix
When a Bemix client is booted, it sends a packet to the server containing "Bemix v3.0" over the debug port.
Touch Switch Output
The Bemix clients will send an ASCII number 1 through 5, corresponding to the 5 touch switches. The PIC can be programmed to send a single packet when a switch is touched or a continuous stream (at adjustable repeat rate) when it is touched.
Example: touch switches 1 and 5 are touched on device 70 which is programmed to tell device 1 (the server)
'\' 'H' 01 70 64 1 '\' 'E' '\' 'H' 01 70 64 5 '\' 'E'
Touch Switch Recalibration
The touch switch may be recalibrated by disabling it then reenabling it. This is done by sending a packet containing "D" followed by "E" over the Bemix port:
'\' 'H' 70 01 64 'D' '\' 'E' '\' 'H' 70 01 64 'E' '\' 'E'
Bemix clients will respond to a packet over the pinging port with an empty packet over the same port.
Example: server pinging device 70 and its response
'\' 'H' 70 01 32 '\' 'E' '\' 'H' 01 70 32 '\' 'E'
One possible use of pinging is to build a routing table by sending a pinging each serial port to map serial port numbers to device addresses.
- Fix bugs with reception
- Store PIC's address in EEPROM, be able to send an address and data pair and have PIC write it to EEPROM
- Make devices listen to address 255
See Bemix PIC code.